BASIC
'AT' COMMANDSET
EXTENDED 'AT&' COMMAND SET
EXTENDED 'AT*' COMMAND SET
BASIC S-REGISTER,
'ATSn=x'
EXTENDED S-REGISTERS, 'ATSn=x'
RESULT CODE OPTIONS TABLE
ZyXEL omni.net DSS1: V 1.20 603D Current settings ..... ISDN Outgoing Service : X.75 E1 L2 M1 N2 Q0 V1 X5 Z4 CB0 CC0 CD0 CE1 CP0 &C1 &D2 &E0 &H3 &J0 &L0 &K00 &O2 &R1 &S0 *A1 *C0 *D0 *GC0 *G0 S00 = 0 S01 = 0 S02 = 43 S03 = 13 S04 = 10 S05 = 8 S06 = 3 S07 = 60 S08 = 2 S09 = 6 S10 = 7 S11 = 70 S12 = 0 S13 = 0 S14 = 2 S15 =130 S16 = 0 S17 = 30 S18 = 0 S19 = 17 S20 = 14 S21 =178 S22 = 0 S23 =105 S24 = 34 S25 = 0 S26 = 0 S27 =155 S28 = 68 S29 = 0 S30 = 0 S31 = 17 S32 = 19 S33 = 0 S34 = 30 S35 = 32 S36 = 0 S37 = 0 S38 = 0 S39 = 0 S40 = 0 S41 = 0 S42 = 0 S43 = 1 S44 = 0 S45 =100 S46 = 28 S47 = 0 S48 = 0 S49 = 0 S50 = 0 S51 = 0 S52 = 0 S53 = 0 S54 = 0 S55 = 0 S56 = 50 S57 = 0 S58 = 0 S59 = 0 S60 = 0 S61 = 0 S62 = 0 S63 = 0 S64 = 5 S65 = 0 S66 = 0 S67 = 0 S68 = 0 S69 = 0 S70 = 0 S71 = 0 S72 = 0 S73 = 0 S74 = 0 S75 = 0 S76 = 0 S77 = 0 S78 = 0 S79 = 12 S80 = 0 S81 = 74 S82 = 62 S83 = 32 S84 = 0 S85 = 1 S86 = 0 S87 = 0 S88 = 2 S89 = 0 S90 = 0 S91 = 0 S92 = 0 S93 = 0 S94 = 0 S95 = 0 S96 = 0 S97 = 0 S98 = 0 S99 = 0 S100= 0 S101= 74 S102= 62 S103= 0 S104= 0 S105= 0 S106= 0 S107= 0 S108= 0 S109= 0 S110= 0 S111= 0 S112= 8 S113= 0 S114= 8 S115= 0 S116= 0 S117= 0 S118= 0 S119= 16 S120= 0 S121= 0 S122= 0 S123= 0 S124= 0 S125= 0 S126= 48 S127= 32 |
ZyXEL omni.net User's Manual Quick Reference Guide For Firmware Version 1.20 and higher |
| BASIC 'AT' COMMANDSET | |
Command Function & Description Ref.
A/ Re-execute the last command once.
A> Re-execute the last command once or repeat the
last call up to 9 times.
<any key> Terminate current connection attempt when enter
in handshaking state.
+++ Escape sequence code, entered in data state, wait
for omni.net to return to command state.
ATA Go on-line in answer mode. (See also S39b2)
ATBnn Select ISDN Teleservice S102
'B' must be followed by two digits.
B0n X.75 :
B00 X.75 Transparent
B01 X.75 T.70
B04 BTX (Datex-J)
B10 V.110 User rate follows DTE speed (async)
B13 V.110 user rate = 2400 bps
B14 V.110 user rate = 4800 bps
B15 V.110 user rate = 9600 bps
B16 V.110 user rate = 14400 bps
B17 V.110 user rate = 19200 bps
B18 V.110 user rate = 38400 bps (async only)
B19 V.110 user rate = 57600 bps (async only)
B20 V.120
B40 PPP async to sync conversion
B41 SLIP to sync HDLC conversion
ATCBn n=0-1 Configuration of embedded protocol analyzer S84b1
CB0 Disable the capture of B channel protocols
CB1 Enable the capture of B channel protocols
ATCCn n=0-1 Configuration of embedded protocol analyzer S84b0
CC0 Disable the capture of DTE-DCE interface
protocols
CC1 Enable the capture of DTE-DCE interface
protocols
ATCDn n=0-1 Configuration of embedded protocol analyzer S84b2
CD0 Disable the capture of D channel protocols
CD1 Enable the capture of D channel protocols
ATCEn n=0-1 Call bumping control for PPP/MP S85b0
CE0 Disable the call bumping function
CE1 * Enable the call bumping function
ATCG Diagnostics
ATCH? Display the accumulated charging unit of the
last call.
ATCI<prefix> Prefix number string to be added to the
Calling-party-number before indicating to the
DTE when the type of number denotes
international.
ATCLn n=0-2048 Maximum size of user data in a packet (number
of bytes)
ATCL? Enquire current setting of ATCLn
ATCN<prefix> Prefix number string to be added to the
Calling-party-number before indicating to the
DTE when the type of number denotes national.
ATCPn n=0-1 Loopback 4 control S83b0
CP0 Disable Loopback 4
CP1 Enable Loopback 4
ATCRn n=0-3 *0 Resumes a previously suspended call, n is the
call identifier (DSS1)
ATCSn n=0-3 *0 Suspend a call, n is the call identifier (DSS1)
ATCT Clear buffer and start the embedded protocol
analyzer. Capture data immediately and start
timer.
ATC$ Stop the capturing of embedded protocol analyzer
ATDs Dial s (number and options) that follows (see
also S38b0, S35b4). The options of s are listed
as follows :
, Pause for a time specified in S8. Remaining
digits will be dialed as in-band DTMF.
Y0 * Unknown type of number
Y1 International number
Y2 National number
Y3 Network specific number
Y4 Subscriber number
Y6 Abbreviated number
Z0 * Type of subaddress - NSAP with AFI=$50, IA5
characters
Z2 Type of subaddress - user specified, IA5
characters
N0 * Unknown numbering plan
N1 ISDN/Telephony numbering plan (CCITT E.164/
E.163)
N3 Data numbering plan (CCITT X.121)
N8 National standard numbering plan
N9 Private numbering plan
/ Called party subaddress delimiters
The format of s will be :
[[Yn][Nn]called_party_Number][[W][,]]inband_dtmf_number
or [[Yn][Nn]called_party_Number][/[Zn]called_party_subaddress/]
ATDAs Dial s (number and options) that follows
for the POTS port, Phone 1
ATDBs Dial s (number and options) that follows
for the POTS port, Phone 2
ATDIs Dial s (number and options) that follows
for ISDN data call
ATDL Repeat last ATD command
ATDNn n=0,1 Set the Directory Numbers (USA)
ATDN0=xxxxxx set the DN0 value
ATDN0= clear the DN0
ATDN? query present DNs
ATDSn n=0-39 Dial number stored in NVRAM at location 'n', S44b3
use '+' to dial two consecutive numbers for
bundling or PPP/MP calls
ATEn Command mode local echo of keyboard commands. S23b0
E0 Echo off
E1 * Echo on
ATHn On/off hook control
H0 * Hang up (on-hook) ISDN Data Call, same as 'ATH'
H3 Hang up the POTS port, Phone 1
H4 Hang up the POTS port, Phone 2
ATIn Display inquired information
I0 Display product code, same as 'ATI'.
Results: 1291 (USA)
1292 (DSS1)
1293 (1TR6)
I1 Display product information and ROM checksum
Results: omni.net <switch>: V x.xx
<checksum>
where <switch>= USA, DSS1, or 1TR6
I3 Display link status report of ISDN call
I9 Display Microsoft PnP code
ATJAn n=0-255 *48 Add-threshold for PPP/MP Bandwidth-On-Demand S126
in Kbps unit,
ATJSn n=0-255 *32 Sub-threshold for PPP/MP Bandwidth-On-Demand S127
in Kbps unit
ATKAxn n=0-63 *0 Add-persist time interval for BOD, S85b1-7
BOD disabled if n=0
x= M(in Minute unit) or S(in Second unit)
ATKSxn n=0-63 *0 Sub-persist time interval for BOD, S125b1-7
x= M(in Minute unit) or S(in Second unit)
ATLn n=0-3 *2 Speaker volume control. The higher the value S24b4-5
,the higher the volume.
ATMn Speaker control. S21b1-2
M0 Speaker always OFF.
M1 * Speaker ON until call is answered.
M2 Speaker always ON.
ATNn n=0-3 *2 Ring volume control.'N0' will disable S24b0-1
the ring function.
ATO Return to on-line state
ATPn n=0-6 D-channel protocol selection(USA)
for American Version
P0 * Northern Telecom proprietary ISDN
P1 National ISDN 1(1 SPID)
P2 National ISDN 1(2 SPID)
P3 reserved
P4 AT&T proprietary point-to-point
P5 AT&T proprietary point-to-multipoint(1 SPID)
P6 AT&T proprietary point-to-multipoint(2 SPID)
ATQn Result code displayed S23b7
Q0 * omni.net returns result code.
Q1 omni.net does not return result code.
Q2 omni.net returns result code but quiet after S40b1
answering on a RING.
ATSr.b=n Set bit 'b' of S-register 'r' to value 'n'.
'n' is a binary digit '0' or '1'.
ATSr.b? Display value of bit 'b' of S-register 'r'.
ATSr=n Set S-register 'r' to value 'n'. 'n' must be a
decimal number between 0 and 255.
ATSr? Display value stored in S-register 'r'.
ATSPIDr=nnn... User enters Service Profile ID nnnn...(USA only)
SPID0 First SPID number
SPID1 Second SPID Number, if any
ATSPID? Display the SPID setting(s) (USA only)
ATUPX Upload firmware to the Flash EPROM
ATVn Verbal/Numeric result codes. S23b6
V0 Display result code in numeric form. (See also
S35b7 and the result code table of 'ATXn')
V1 * Display result code in verbose form.
ATXn n=0-7 *5 Result code options, see the Options Table S23b3-5
ATZn n=0-4 Reset omni.net and set power-on profile. S15b5-7
Zn Reset omni.net and load user profile n (0-3).
Z4 Reset omni.net and load factory settings.
AT$ Basic command summary help
|
|
| EXTENDED 'AT&' COMMAND SET | |
Command Function & Description Ref.
&Cn Carrier Detect (CD) options S21b4
&C0 CD always ON (See also S42b7)
&C1 * CD tracks presence of carrier.
(See also S38b3)
&Dn Data Terminal Ready (DTR) options. S21b6-7
(See also S25)
&D0 Ignore DTR signal, assume DTR is always ON.
&D1 108.1, DTR OFF-ON transition causes dial of the
default number. (See also 'AT*Dn' and S48b4)
Note: This function is ignored when power on.
&D2 * 108.2, Data Terminal Ready, DTR OFF causes the
omni.net to hang up.
&D3 Same as &D2 but DTR OFF causes the omni.net to
hang up and reset from profile 0.
&En B channel line speed for ISDN data call S118b2
&E0 * 64Kbps
&E1 56Kbps (Default for American ISDN)
&F Load factory settings to RAM as active
configuration.
&Hn DTE port 1 Data flow control, DTE/DCE. S27b3-5
&H0 Flow control disabled.
&H3 * Hardware (CTS/RTS) flow control.
&H4 Software (XON/XOFF) flow control.
&Jn Bundle selection (See also S100) S87b5-6
&J0 * Bundle connection is disabled
&J1 Bundle connection is enabled in answer
mode only
&J2 Bundle connection is enabled in call
mode only
&J3 Bundle connection is enabled in both
directions
&Knn PPP/V.120/X.75 data compression control
&K must be followed by two digits S83b2
&K00 Disable compression
&K44 Enable V.42bis (PPP/V.120/X.75), STAC (PPP)
&Ln POTS port selection during call answering S84b5
&L0 Set priority to POTS port, Phone 1
&L1 Set priority to POTS port, Phone 2
&On Set default call type for conventional dialing S83b4-5
commands
&O0 ATDs, ATDPs, and ATDTs default to make
calls for the POTS port, Phone 2
&O2 ATDs, ATDPs, and ATDTs default to make ISDN
data calls
&O3 ATDs, ATDPs, and ATDTs default to make calls
for the POTS port, Phone 1
&Sn Data Set Ready (DSR) function selection. S21b3
&S0 * DSR overridden, DSR always ON.
&S1 DSR according to CCITT (ITU-TSS).
(See also S41b5, S44b4)
&Tn omni.net testing.
&T9 Initiate ISDN loopback test
&T10 Initiate ISDN loopback with self test
&Vn View profile settings.
&V0 View current active settings.
&Vn View the (n-1)th user profile settings (n=1-4)
&V5 View factory default settings.
&V6 View POTS port, Phone 1 setting
&V7 View POTS port, Phone 2 setting
&Wn n=0-3 Write current settings to user profile n in
NVRAM. (See also S35b6)
&Z? Display all the phone numbers stored in NVRAM.
&Zn=s n=0-39 Write phone number s to NVRAM at location n
(n=0-39) use AT*Dn or ATS29=n to set the
default dial pointer.
&ZIn=s n=0-7 Assign the phone number (including
subaddress, if any) for various B-channel
protocols. In answer mode, these numbers
will be compared with the received called
party number or called party subaddress
information. The call will be accepted using
the specific protocol if the assigned number
of this protocol matches with the called
party number.
&ZI0=s Assign the phone number for X.75
&ZI1=s Assign the phone number for V.110
&ZI2=s Assign the phone number for V.120
&ZI3=s Assign the phone number for PPP, PPP/MP
&ZI4=s Assign the phone number for ISDN data
(Multi-Auto answering, auto detect the protocols)
&ZI6=s Assign the phone number for POTS port, Phone 2
&ZI7=s Assign the phone number for POTS port, Phone 1
&ZI? Display the phone number (including subaddress
, if any) for various B-channel protocols
&ZOx=s Write own phone number (including subaddress, if any).
The number specified by &ZOx will be used as the
calling party number while dialing
x = I(ISDN), A(POTS port, Phone 1) or
B(POTS port, Phone 2)
&ZO? Display the own phone numbers assigned via
the AT&ZOx=s command
|
|
| EXTENDED 'AT*' COMMAND SET | |
Command Function & Description Ref.
*Dn n=0-39 Set default dial pointer at telephone S29
directory location n.
*D0 * (See also S35b4 and S38b0)
*Gn Security function selection. S36b5-7
*G0 * Disable security function.
*G1 Enable type 1 security, with password check
(ZyXEL to ZyXEL only).
*G2 Enable type 1 security, with password check
and call back (ZyXEL to ZyXEL only).
*G3 Enable type 2 security, with password check.
*G4 Enable type 2 security, with password check
and call back.
*G5 Enable type 2 security, with password check
and call back, remote site enters the call
back number.
*GCn Call-back function selection. S119b0
*GC0 * Disable call-back function.
*GC1 Enable call-back function
*HCn n=0-4 Assign call back phone number.
*Hn n=0-39 Modify user password table at location n.
*HS Modify supervisory password (Default: 'ZyXEL').
*T Recall the last CND (Caller ID) information.
*V View password table
*VC View call-back number table
|
|
| BASIC S-REGISTER, 'ATSn=x' | |
| EXTENDED S-REGISTERS, 'ATSn=x | |
| RESULT CODE OPTIONS TABLE | |