BASIC
'AT' COMMANDSET
EXTENDED 'AT&' COMMAND SET
EXTENDED 'AT*' COMMAND SET
BASIC S-REGISTER,
'ATSn=x'
EXTENDED S-REGISTERS, 'ATSn=x'
RESULT CODE OPTIONS TABLE
ZyXEL omni.net DATA DSS1: V 1.05 B0C1 ati9 ($ZYX0CED\0000B0C1\MODEM\\ZyXEL omni.net DATA V 1.05 1C) Current settings ..... ISDN Outgoing Service : PPP+X.75+V.120 460800 N81 E1 Q0 V1 X5 Z4 CB0 CC0 CD0 CP0 &C1 &D2 &E0 &H3 &J0 &K00 &O2 &R1 &S0 *D0 *GC0 *G0 S00 = 0 S01 = 0 S02 = 43 S03 = 13 S04 = 10 S05 = 8 S06 = 3 S07 = 60 S08 = 2 S09 = 6 S10 = 7 S11 = 70 S12 = 0 S13 = 0 S14 = 2 S15 =130 S16 = 0 S17 = 30 S18 = 0 S19 = 17 S20 = 14 S21 =178 S22 = 0 S23 =105 S24 = 34 S25 = 0 S26 = 0 S27 =155 S28 = 68 S29 = 0 S30 = 0 S31 = 17 S32 = 19 S33 = 0 S34 = 30 S35 = 32 S36 = 0 S37 = 0 S38 = 0 S39 = 0 S40 = 0 S41 = 0 S42 = 0 S43 = 1 S44 = 0 S45 =100 S46 = 28 S47 = 0 S48 = 0 S49 = 0 S50 = 0 S51 = 0 S52 = 0 S53 = 0 S54 = 0 S55 = 0 S56 = 50 S57 = 0 S58 = 0 S59 = 0 S60 = 0 S61 = 0 S62 = 0 S63 = 0 S64 = 5 S65 = 0 S66 = 0 S67 = 0 S68 = 0 S69 = 0 S70 = 0 S71 = 0 S72 = 0 S73 = 0 S74 = 0 S75 = 0 S76 = 0 S77 = 0 S78 = 0 S79 = 12 S80 = 0 S81 = 74 S82 = 62 S83 = 32 S84 = 0 S85 = 1 S86 = 0 S87 = 0 S88 = 2 S89 = 0 S90 = 0 S91 = 0 S92 = 0 S93 = 0 S94 = 0 S95 = 0 S96 = 0 S97 = 0 S98 = 0 S99 = 0 S100= 0 S101= 74 S102= 62 S103= 0 S104= 0 S105= 0 S106= 0 S107= 0 S108= 0 S109= 0 S110= 0 S111= 0 S112= 8 S113= 0 S114= 8 S115= 0 S116= 0 S117= 0 S118= 0 S119= 16 S120= 0 S121= 1 S122= 52 S123= 0 S124= 0 S125= 0 S126= 48 S127= 32 |
ZyXEL omni.net Quick Reference Guide For Firmware Version 1.03 or higher |
| BASIC 'AT' COMMANDSET | |
Command Function & Description Ref.
A/ Re-execute the last command once.
A> Re-execute the last command once or repeat the
last call up to 9 times. (See also S8)
<any key> Terminate current connection attempt when enter
in handshaking state.
+++ Escape sequence code, entered in data state, wait
for omni.net to return to command state.
ATA Go on-line in answer mode. (See also S39b2)
ATBnn Select ISDN Teleservice S102
'B' must be followed by two digits.
B0n X.75 :
B00 X.75 Transparent
B01 X.75 T.70
B10 V.110 User rate follows DTE speed (async)
User rate determined by in-band negotiation (sync)
B11 V.110 user rate = 64000 bps (sync mode) S117
B13 V.110 user rate = 2400 bps
B14 V.110 user rate = 4800 bps
B15 V.110 user rate = 9600 bps
B16 V.110 user rate = 14400 bps
B17 V.110 user rate = 19200 bps
B18 V.110 user rate = 38400 bps (async only)
B19 V.110 user rate = 57600 bps (async only)
B20 V.120
B40 PPP async to sync conversion
B41 SLIP to sync HDLC conversion
B42 EuroFile Transfer
Multi Auto Dial Out (valid only if s80.6=1)
B90 PPP+X.75 S122
B91 PPP+X.75+T.70+ISO_8208+T.90+BTX
B92 X.75+T.70+ISO_8208+T.90+BTX+PPP
B93 PPP+V.120
B94 V.120+PPP
B95 PPP+X.75+V.120
B96 PPP+V.120+X.75
B97 X.75+V.120+PPP
ATBPn n=0-1 Configuration PPP BACP/BAP negotiation
BP0 Disable PPP BACP/BAP
BP1 * Enable PPP BACP/BAP
ATCBn n=0-1 Configuration of embedded protocol analyzer S84b1
CB0 Disable the capture of B channel protocols
CB1 Enable the capture of B channel protocols
ATCCn n=0-1 Configuration of embedded protocol analyzer S84b0
CC0 Disable the capture of DTE-DCE interface
protocols
CC1 Enable the capture of DTE-DCE interface
protocols
ATCDn n=0-1 Configuration of embedded protocol analyzer S84b2
CD0 Disable the capture of D channel protocols
CD1 Enable the capture of D channel protocols
ATCEn n=0-1 Call bumping control for PPP/MP and CCB S85b0
CE0 Disable the call bumping function
CE1 * Enable the call bumping function
ATCFxy(tranfer_no.) For DSS1,activate the call forwarding service
ATCFxy Deactivate the call forwarding service
(Note!You should set your own number first,AT&ZOx=s)
x=B Call forwarding busy(CFB)
U Call forwarding unconditional(CFU)
NR Call forwarding no-reply(or no-response,CFNR)
y=I ISDN data(unrestricted digital)
ATCF? Query the status of call forwarding(DSS1 only)
ATCG Diagnostics
ATCH? Display the accumulated charging unit of the
last call.
ATCI<prefix> Prefix number string to be added to the
Calling-party-number before indicating to the
DTE when the Numbering Plan denotes
international.
ATCLn n=0-2048 Maximum size of user data in a packet (number
of bytes)
ATCL? Enquire current setting of ATCLn
ATCN<prefix> Prefix number string to be added to the
Calling-party-number before indicating to the
DTE when the Numbering Plan denotes national.
ATCRn n=0-3 *0 Resumes a previoully suspended call, n is the
call identifier(Europe)
ATCSn n=0-3 *0 Suspend a call, n is the call identifier(Europe)
ATCT Clear buffer and start the embedded protocol
analyzer. Capture data immediately and start
timer.
ATC$ Stop the capturing of embeded protocol analyzer
ATDs Dial s (number and options) that follows (see
also S38b0, S35b4). The options of s are listed
as follows :
, Pause for a time specified in S6. Remaining
digits will be dialed as in-band DTMF.
Y0 * Unknown type of number
Y1 International number
Y2 National number
Y3 Network specific number
Y4 Subscriber number
Y6 Abbreviated number
Z0 * Type of subaddress - NSAP with AFI=$50, IA5
characters
Z2 Type of subaddress - user specified, IA5
characters
N0 * Unknown numbering plan
N1 ISDN/Telephony numbering plan (CCITT E.164/
E.163)
N3 Data numbering plan (CCITT X.121)
N8 National standard numbering plan
N9 Private numbering plan
/ Called party subaddress delimeters
The format of s will be :
[[Yn][Nn]called_party_Number][[W][,]]inband_dtmf_number
or [[Yn][Nn]called_party_Number][/[Zn]called_party_subaddress/]
ATDIs Dial s (number and options) that follows
for ISDN data call
ATDL Repeat last ATD command
ATDNn n=0,1 Set the Directory Numbers (USA)
ATDN0=xxxxxx set the DN0 value
ATDN0= clear the DN0
ATDN? query present DNs
ATDSn n=0-39 Dial number stored in NVRAM at location 'n', S44b3
use '+' to dial two consecutive numbers for
bundling or PPP/MP calls
ATEn Command mode local echo of keyboard commands. S23b0
E0 Echo off
E1 * Echo on
ATHn On/off hook control
H0 * Hang up (on-hook) ISDN Data Call, same as 'ATH'
ATIn Display inquired information
I0 Display product code, same as 'ATI'.
Results: 1291 (USA)
1292 (DSS1)
1293 (1TR6)
I1 Display product information and ROM checksum
Results: omni.net D<switch>: V x.xx
<checksum>
where <switch>= USA, DSS1, or 1TR6
I3 Display link status report of ISDN call
I9 Display Microsoft PnP code
I11 Display PPP status.
ATJAn n=0-255 *48 Add-threshold for PPP/MP Bandwidth-On-Demand S126
in Kbps unit,
ATJSn n=0-255 *32 Sub-threshold for PPP/MP Bandwidth-On-Demand S127
in Kbps unit
ATJHn PPP/MP DTE compression option switch
n=0 Disable DTE compression, compression done by TA
n=1* Enable DTE compression if avaiable
ATKAxn n=0-63 *0 Add-persist time interval for BOD, S85b1-7
BOD disabled if n=0
x= M(in Minute unit) or S(in Second unit)
ATKSxn n=0-63 *0 Sub-persist time interval for BOD, S125b1-7
x= M(in Minute unit) or S(in Second unit)
ATO Return to on-line state
ATPn n=0-6 D-channel protocol selection(USA) S86
for American Version
P0 * Northern Telecom proprietary ISDN
P1 National ISDN 1(1 SPID)
P2 National ISDN 1(2 SPID)
P3 reserved
P4 AT&T proprietary point-to-point
P5 AT&T proprietary point-to-multipoint(1 SPID)
P6 AT&T proprietary point-to-multipoint(2 SPID)
ATQn Result code displayed S23b7
Q0 * omni.net returns result code.
Q1 omni.net does not return result code.
ATSr.b=n Set bit 'b' of S-register 'r' to value 'n'.
'n' is a binary digit '0' or '1'.
ATSr.b? Display value of bit 'b' of S-register 'r'.
ATSr=n Set S-register 'r' to value 'n'. 'n' must be a
decimal number between 0 and 255.
ATSr? Display value stored in S-register 'r'.
ATSPIDr=nnn... User enters Service Profile ID nnnn...(USA)
SPID0 First SPID number
SPID1 Second SPID Number, if any
ATSPID? Display the SPID setting(s)
ATUPX Download firmware to the Flash EPROM
ATVn Verbal/Numeric result codes. S23b6
V0 Display result code in numeric form. (See also
S35b7 and the result code table of 'ATXn')
V1 * Display result code in verbose form.
ATXn n=0-8 *5 Result code options, see the Options Table S23b3-5
ATZn n=0-4 Reset omni.net and set power-on profile. S15b5-7
Zn Reset omni.net and load user profile n (0-3).
Z4 Reset omni.net and load factory settings.
AT$ Basic command summary help
|
|
| EXTENDED 'AT&' COMMAND SET | |
Command Function & Description Ref.
&Cn Carrier Detect (CD) options S21b4
&C0 CD always ON (See also S42b7)
&C1 * CD tracks presence of carrier.
&Dn Data Terminal Ready (DTR) options. S21b6-7
(See also S25)
&D0 Ignore DTR signal, assume DTR is always ON.
&D1 108.1, DTR OFF-ON transition causes dial of the
default number. (See also 'AT*Dn')
Note: This function is ignored when power on.
&D2 * 108.2, Data Terminal Ready, DTR OFF causes the
omni.net to hang up.
&D3 Same as &D2 but DTR OFF causes the omni.net to
hang up and reset from profile 0.
&En B channel line speed for ISDN data call S118b2
&E0 * 64Kbps
&E1 56Kbps (Default for American ISDN)
&F Load factory settings to RAM as active
configuration.
&Hn DTE port 1 Data flow control, DTE/DCE. S27b3-5
&H0 Flow control disabled.
&H3 * Hardware (CTS/RTS) flow control.
&H4 Software (XON/XOFF) flow control.
&In Dial-up/leased line options
&I0 * dial-up line mode.
&I1 leased line mode in B1 channel.
&I2 leased line mode in B2 channel.
&I3 leased line mode in both B1 and B2 channel.
&Jn Bundle selection (See also S100) S87b5-6
&J0 * Bundle connection is disabled
&J1 Bundle connection is enabled in answer
mode only
&J2 Bundle connection is enabled in call
mode only
&J3 Bundle connection is enabled in both
directions
&Knn PPP/V.120/X.75 data compression control
&K must be followed by two digits S83b2
&K00 Disable V.42bis
&K44 Enable V.42bis (PPP/V.120/X.75), STAC (PPP)
&Mn Synchronous/asynchronous mode options. S14b6-7
&M0 * Asynchronous mode with data buffering.
&M1 Asynchronous command, synchronous data
&M2 Direct asynchronous mode, no data buffering.
&M3 Synchronous mode.
&On Set default call type for conventional dialing S83b4-5
commands
&O2 ATDs, ATDPs, and ATDTs default to make ISDN
data calls
&Sn Data Set Ready (DSR) function selection. S21b3
&S0 * DSR overridden, DSR always ON.
&S1 DSR according to CCITT (ITU-TSS).
(See also S41b5, S44b4)
&Tn omni.net testing.
&T9 Initiate ISDN loopback test
&T10 Initiate ISDN loopback with self test
&T11 Initiate ISDN loopback from B1 through switch
to B2.
&Vn View profile settings.
&V0 View current active settings.
&Vn View the (n-1)th user profile settings (n=1-4)
&V5 View factory default settings.
&Wn n=0-3 Write current settings to user profile n in
NVRAM. (See also S35b6)
&Z? Display all the phone numbers stored in NVRAM.
&Zn=s n=0-39 Write phone number s to NVRAM at location n
(n=0-39) use AT*Dn or ATS29=n to set the
default dial pointer.
&ZIn=s n=0-7 Assign the phone number (including
subaddress, if any) for various B-channel
protocols. In answer mode, these numbers
will be compared with the received called
party number or called party subaddress
information. The call will be accepted using
the specific protocol if the assigned number
of this protocol matches with the called
party number.
&ZI0=s Assign the phone number for X.75
&ZI1=s Assign the phone number for V.110
&ZI2=s Assign the phone number for V.120
&ZI3=s Assign the phone number for PPP, PPP/MP
&ZI4=s Assign the phone number for ISDN data
(Multi-Auto answering, auto detect the protocols)
&ZI? Display the phone number (including subaddress
, if any) for various B-channel protocols
&ZOx=s Write own phone number (including
subaddress, if any). The number specified by
&ZOx will be used as the calling party number
while dialing
x = I(ISDN)
&ZO? Display the own phone numbers assigned via
the AT&ZOx=s command
|
|
| EXTENDED 'AT*' COMMAND SET | |
Command Function & Description Ref.
*Dn n=0-39 Set default dial pointer at telephone S29
directory location n.
*D0 * (See also S35b4 and S38b0)
*Gn Security function selection. S36b5-7
*G0 * Disable security function.
*G1 Enable type 1 security, with password check
(ZyXEL to ZyXEL only).
*G2 Enable type 1 security, with password check
and call back (ZyXEL to ZyXEL only).
*G3 Enable type 2 security, with password check.
*G4 Enable type 2 security, with password check
and call back.
*G5 Enable type 2 security, with password check
and call back, remote site enters the call
back number.
*GCn Call-back function selection. S119b0
*GC0 * Disable call-back function.
*GC1 Enable call-back function.
*HCn n=0-4 Assign call back phone number.
*Hn n=0-39 Modify user password table at location n.
*HS Modify supervisory password (Default: 'ZyXEL').
*In Command set selection. S17b6-7
*I0 * AT command set.
*I1 V.25bis command set.
*T Recall the last CND (Caller ID) information.
*V View password table
*VC View call-back number table
|
|
| BASIC S-REGISTER, 'ATSn=x' | |
Command Function & Description +Def./Ref.
S0= Set the number of rings on which the omni.net will
answer. 0 value disable auto-answer +000
S1= Counts and stores number of rings from an
incoming call +000
S2= Define escape code character, default <+> (43
dec.) +043
S3= Define ASCII Carriage Return +013
S4= Define ASCII Line Feed +010
S5= Define ASCII Backspace +008
S7= Set duration, in number of seconds, omni.net waits
for a connect +060
S8= Set duration, in seconds, for pause (,) option in
Dial command and pause between command
re-executions for Repeat (>)command +002
|
|
| EXTENDED S-REGISTERS, 'ATSn=x | |
Command Function and description +Def./Ref.
S15= bit dec hex Bit-mapped register +130
7-5 0 0 Profile 0 as active settings after
power on Z0
32 20 Profile 1 as active settings after
power on Z1
64 40 Profile 2 as active settings after
power on Z2
96 60 Profile 3 as active settings after
power on Z3
128 80 * Factory default as active settings
after power on Z4
S16= bit dec hex Test status register +000
0 0 No test in progress &T0
9 9 Loopback test in progress &T9
10 A Loopback with self test in progress &T10
11 B loopback from B1 through switch to B2 &T11
S18= dec Force omni.net to fix DTE port 1 baud +000
rate when idle
0 * Disable fixed baud function
1-14,32 1-E,20 Enable baud rate to be fixed when
answering. baud rate value setting
same as S20 except S18=32 for 230400
bps.
S20= dec hex DTE port 1 speed (bps). Auto detected
from AT command +003
0 0 230400
1 1 115200
3 3 57600
4 4 38400
5 5 19200
9 9 9600
11 B 4800
12 C 2400
13 D 1200
14 E 460800
15 F 921600
S21= bit dec hex Bit mapped register +178
3 0 0 DSR always On &S0
8 8 According to CCITT (see also S44b4, &S1
S41b5)
4 0 0 CD always On &C0
16 10 CD tracks presence of data connection &C1
(see also S38b3)
6-7 0 0 Assume DTR always On &D0
64 40 108.1, DTR Off-On transition causes &D1
dial of the default number
128 80 108.2 Data Terminal Ready, DTR Off &D2
causes the omni.net to hang up and return
to command state
192 C0 108.2, DTR off causes the omni.net to &D3
hang up and reset the omni.net to profile
#0 after DTR dropped
S23= bit dec hex Bit mapped register +105
0 0 0 Command echo disabled E0
1 1 Command echo enabled E1
2 0 0 Insertion is not allowed during a
phone call
4 4 Insertion is allowed during a phone
call
3-5 0 0 ATX0 (See result code table)
8 8 ATX1 dec hex AT
16 10 ATX2 40 28 X5
24 18 ATX3 48 30 X6
32 20 ATX4 56 38 X7
6 0 0 Display result code in numeric format V0
(see S35b7)
64 40 Display result code in verbose format V1
S27= bit dec hex Bit mapped register +156
3-5 0 0 DTE port 1 Flow control disabled &H0
24 18 DTE port 1 Hardware (RTS/CTS)
flow control &H3
32 20 Reserved &H4
40 28 Reserved &H5
S29= 0-39 0-39 Set default dial phone number pointer, +000
use AT&Zn=s to store phone numbers *D
S31= 0-255 0-FF Holds the ASCII decimal value of the +017
XON
S32= 0-255 0-FF Holds the ASCII decimal value of the +019
XOFF
S35= bit dec hex Bit mapped register +000
7 128 60 Enable extended numerical result codes V0
from 50-71 when an error correction S23b6
connection is made, use with ATV0, see
result code table
S36= bit dec hex Bit mapped register +000
0 0 0 Deny remote request for configuration *F0
5-7 Security function control register
0 0 Disable security function *G0
32 20 Enable type 1 security, with password *G1
check (ZyXEL to ZyXEL only)
64 40 Enable type 1 security, with password *G2
check and call-back (ZyXEL to ZyXEL
only)
96 60 Enable type 2 security, with password *G3
check
128 80 Enable type 2 security, with password *G4
check and call-back
160 A0 Enable type 2 security, with password *G5
check and call-back, remote site enter
the call-back number
S38= bit dec hex Bit mapped register +000
3 8 8 DCD on/off sequence follows UNIX &C1 S21b4
standard, DCD high before connect
message is sent, DCD off after last
DCE response is sent
S40= bit dec hex Bit mapped register +000
1 2 2 No result code displayed in answer Q2
mode
S41= bit dec hex Bit mapped register +000
3 8 8 Enable CCITT signals 140 and 141 on
EIA-232D interface
5 32 20 DSR follows DCD and pulses (see also &Sn
S44b4)
6 64 40 Force S0>=2 S0
S42= bit dec hex Bit mapped register +000
3 8 8 Disable escape sequence code in answer
mode
5 32 20 Disable Data/Voice button
6 64 40 Disable <RINGING> result code Xn
7 128 80 DCD forced on but pulse off for 0.5 &C0
seconds at carrier loss
S44= bit dec hex Bit mapped register +000
3 8 8 ATDSn initiates auto-dial of the &Zn
stored numbers consecutively until a S38b0
connection is made
4 16 10 DSR follows DTR (see also S41b5) &Sn
S64 dec hex Security callback timer in unit +005
0-255 0-FF of 1 second
S80= bit dec hex Bit-mapped register: +000
6 *0 0 Not sending Low Layer Compatibility
information for ISDN data call
64 40 Sending Low Layer Compatibility
for ISDN data call
S82= ISDN data type; a temporary variable
used while call in progress
60 V.120 64000
61 V.120 56000
62 X.75 64000 Transparent
63 X.75 56000 Transparent
64 X.75 64000 T.70
65 X.75 56000 T.70
70 X.75 64000 BTX
71 X.75 56000 BTX
72 V.110 64000
73 V.110 56000
74 PPP async to sync 64K
75 PPP async to sync 56K
76 SLIP to sync HDLC conversion 64K
77 SLIP to sync HDLC conversion 56K
S83= bit dec hex Bit-mapped register: +000
2 0 0 ISDN without V.42bis &K00
4 4 ISDN with V.42bis if applicable &K44
4-5 32 20 ATDs, ATDPs, and ATDTs is mapped &O2
to ATDIs
6 0 0 * DOVBS answer using 56Kbps (for USA only)
64 40 DOVBS answer using 64Kbps
7 0 0 * ISDN data call using nornal Bearer Service
(for USA only)
128 80 ISDN data call using voice Bearer Service
S84= bit dec hex
0-2 Embedded protocol analyzer control CCn
0 1 1 Capture DTE-DCE interface protocol
information
1 2 2 Capture the B-channel (X.75 or V.120)
frames
2 4 4 Capture the D-channel protocol
information
3 0 *0 Display S register value in decimal
format
8 8 Display S register value in hex format
4 *0 0 Indicate Caller ID after the 1st RING
message
16 10 Disable Caller ID indication
S85= bit dec hex
1-6 *0 Add-persist time interval KAxn
7 0 *0 S85b1-6 is in Second unit KASn
128 80 S85b1-6 is in Minute unit KAMn
S86= dec hex D-channel protocol selection(USA) Pn
The following number is valid for
American version:
0 0 Northern Telecom proprietary ISDN
1 1 National ISDN 1 (1 SPID mode)
2 2 National ISDN 1 (2 SPIDs mode)
3 3 reserved
4 4 AT&T proprietary point-to-point
5 5 AT&T proprietary point-to-multipoint
(1 SPID mode)
6 6 AT&T proprietary point-to-multipoint
(2 SPIDs mode)
All other values are reserved.
S87= bit dec hex
5-6 *0 0 Bundle connection is disabled &Jn
32 20 Bundle connection is enabled in answer
mode only
64 40 Bundle connection is enabled in call
mode only
96 60 Bundle connection is enabled in both
directions
S100 dec hex B channel bundling protocol selection
0 0 * Multiple Link Protocol (MLP)
S102 bit dec hex Outgoing ISDN data type Bnn
Value has the same definition as S82
S104+n dec hex Outgoing Service Indicator (for 1TR6 only)
n = 2(ISDN data)
1 1 Fernsprechen
2 2 a/b - Dienste
7 7 Datenuebertragung 64 kbps. The defaults
are :
* s105= - reserved
* s106=7 - for ISDN data
S108+n dec hex Outgoing Service Additional (for 1TR6 only)
Information
n = 2(ISDN data)
SI=1 1 1 * ISDN-Fernsprechen 3.1 kHz
2 2 Fernsprechen analog
SI=2 2 2 Fax Gruppe 3
3 3 * Daten ueber Modem
4 4 Btx ueber Modem
SI=7 0 0 Datenuebertragung 64 kbps (X.75 SLP)
11------ Async V.110
01------ Extensions of async
--0----- * Number of data bits : 8
--1----- Number of data bits : 7
---0---- * Number of stop bits : 1
---1---- Number of stop bits : 2
----0--- * No parity
----1--- Even parity
11---000 1200 bps
11---011 2400 bps
11---100 4800 bps
11---101 9600 bps
11---110 14400 bps
11---111 * 19200 bps
01---000 38400 bps
1010---- Sync V.110
10100000 1200 bps
10100011 2400 bps
10100100 4800 bps
10100101 9600 bps
10100110 14400 bps
10100111 19200 bps
10101000 48000 bps
10101001 56000 bps
10101010 56000 bps for 56kbit-network
10101111 In band negotiation
S108+n dec hex High Layer Compatibility (Non-1TR6)
n = 2(ISDN data)
*0 0 No High-Layer-Compatibility
information element will be sent
1 1 Telephone
4 4 Facsimile Group 2/3
40 28 Teletex service(Rec.F.220)
49 31 Teletex service(Rec.F.200)
50 32 Information interworking for
video services(Rec.F.300 T.110)
53 35 Telex service(Rec.F.60)
56 38 Message Handling Syxtems(MHS)
(Rec.X.400 series)
65 41 OSI application(Rec.X.200 series)
S114 I-field data length (MSB byte)
S115 I-field data length (LSB byte)
S117 V.110 user rate B1n
S118 bit dec hex
0 *0 0 Enable dial-in call
1 1 Disable dial-in call(dial out only)
2 *0 0 Default B channel line speed is 64Kbps
for ISDN data call &E0
4 4 Default B channel line speed is 56Kbps
for ISDN data call &E1
3 *0 0 Disable DTE CHAP option for PPP/MLPPP,
CHAP done by TA
8 8 Enable DTE CHAP option for PPP/MLPPP
S119= bit dec hex
0 *0 0 Disable call-back function(see AT*GC)
1 1 Enable call-back function
1 *0 0 Disable point-to-point signaling DDI function
2 2 Enable point-to-point signaling DDI function
2 *0 0 Disable point-to-multipoint signaling DDI
function
4 4 Enable point-to-multipoint signaling DDI
function
3 0 0 when no MSN(EAZ) is matched, the inbound
call will be ignored
8 8 when no MSN(EAZ) is matched, use default
protocol to accept
NOTE: default = 1 for USA, default = 0 for others
4 0 0 V.110 user rate = 19200 bps if DTE speed
greater 19200 bps
*16 10 V.110 user rate = 38400 bps if DTE speed
greater 38400 bps
5 *0 0 enable normal MSN function &ZIn=
32 20 treat the number assigned by &ZIn=xx..
as subaddress and matches with the called
party subaddress for inbound call routing
S120= bit dec hex
4 *0 0 Enable TA to accept global calls for ISDN data
16 10 Forbid TA to accept incoming calls with MSN
unmatched for ISDN data.
(including global calls, see AT&ZI=s)
S122= bit dec hex
0-1 0-3 0-3 Select a preferred B-channel for outgoing
data call(USA only)
*0 0 Any channel
1 1 Reserved
2 2 B1-channel preferred
3 3 B2-channel preferred
2-7 Reserved
S124= dec hex Empty IP packet interval for PPP +000
0-255 0-FF in units of 1s
S125= bit dec hex
1-6 *0 Sub-persist time interval KSxn
7 0 *0 S125b1-6 is in Second unit KSSn
128 80 S125b1-6 is in Minute unit KSMn
S126= dec hex Add-threshold for BOD JAn,+48
0-255 0-FF in Kbps unit
S127= dec hex Sub-threshold for BOD JSn,+32
0-255 0-FF in Kbps unit
In 'Reference' column, 'AT' is omitted when AT command is referred to.
+nnn is manufacturer default when listed in 'Reference' column.
bit S-register bit number, 'b', used in 'ATSr.b=n', 'ATSr.b=?'
dec Decimal value, 'x', used in 'ATSn=x'
hex Hex value, used in LCD model for setting 'STATUS REGISTER'
manually from front panel
|
|
| RESULT CODE OPTIONS TABLE | |
ATV0 ATV1 ATX0 X1 X2 X3 X4 X5 X6 X7 X8
0 OK V V V V V V V V V
1 CONNECT V V V V V @ $ # &
2 RING V V V V V V V V V
3 NO CARRIER V V V V V V V V V
4 ERROR V V V V V V V V V
5 CONNECT 1200 % % % % @ $ # &
6 NO DIAL TONE V V V V V V
7 BUSY V V V V V V
8 NO ANSWER V V V V V V
9 RINGING* V V V V V V
10 CONNECT 2400 % % % % @ $ # &
11 CONNECT 4800 % % % % @ $ # &
12 CONNECT 9600 % % % % @ $ # &
14 CONNECT 19200 % % % % @ $ # &
15 CONNECT 7200 % % % % @ $ # &
16 CONNECT 12000 % % % % @ $ # &
17 CONNECT 14400 % % % % @ $ # &
18 CONNECT 16800 % % % % @ $ # &
19 CONNECT 38400 % % % % @ &
20 CONNECT 57600 % % % % @ &
21 CONNECT 76800 % % % % @ &
22 CONNECT 115200 % % % % @ &
23 CONNECT 230400 % % % % @ &
24 CONNECT 460800 % % % % @ &
25 CONNECT 921600 % % % % @ &
26 CONNECT 307200 % % % % @ &
27 CONNECT 153600 % % % % @ &
28 CONNECT 102400 % % % % @ &
29 CONNECT 61440 % % % % @ &
30 CONNECT 51200 % % % % @ &
31 CONNECT 624000 % % % % @ &
32 CONNECT 124800 % % % % @ &
33 CONNECT 62400 % % % % @ &
34 CONNECT 41600 % % % % @ &
35 CONNECT 31200 % % % % @ $ # &
36 CONNECT 24960 % % % % @ &
37 CONNECT 20800 % % % % @ &
38 CONNECT 33600 % % % % @ $ # &
39 CONNECT 28800 % % % % @ $ # &
40 CONNECT 26400 % % % % @ $ # &
41 CONNECT 24000 % % % % @ $ # &
42 CONNECT 21600 % % % % @ $ # &
43 CONNECT 48000 % % % % @ $ # &
44 CONNECT 56000 % % % % @ $ # &
45 CONNECT 64000 % % % % @ $ # &
46 CONNECT 112000 % % % % @ $ # &
47 CONNECT 128000 % % % % @ $ # &
Note:
V Supported
% Reporting DTE rate:
<cr><lf>CONNECT DTE_Speed<cr><lf>
@ <cr><lf>CONNECT DTE_Speed/Protocol DCE_Speed/Error_Control
[/Data_Compression]<cr><lf>
$ <cr><lf>CONNECT DCE_Speed[/Error_Code]<cr><lf>
# <cr><lf>CONNECT DCE_Speed/Error_Code/Protocol
[/Error_Control[/Data_Compression]]<cr><lf>
& <cr><lf>CARRIER DCE_Speed<cr><lf>
<cr><lf>PROTOCOL: Protocol<cr><lf>
<cr><lf>ERROR CONTROL: Error_Control<cr><lf>
[<cr><lf>COMPRESSION: Data_Compression<cr><lf>]
<cr><lf>CONNECT DTE_Speed<cr><lf>
* Use S42b6 to disable 'RINGING' result code
Error_Code:
NONE
Error_Control: (This field will not show if no error control is negotiated)
LAPB
LAPD
NONE (ATX8 only)
Data_Compression:
V42b
DTE_Speed:
all possible DTE speed supported
Protocol: (only ISDN protocols are listed here)
X.75
X.75M ;X.75 with MLP Bundle
X.75C ;X.75 with cFos Bundle
V110
V120
V120M ;V.120 with MLP Bundle
V120C ;V.120 with cFos Bundle
SLIP
PPP
BTX
Use ATS35 bit 7 (ATS35.7=1) to enable the following numerical result
codes when an error control connection is made.
ATV0 Code ATV1 String ATV0 Code ATV1 String
50 CONNECT 61 CONNECT 24000
51 CONNECT 1200 62 CONNECT 26400
52 CONNECT 2400 63 CONNECT 28800
53 CONNECT 4800 64 CONNECT 31200
54 CONNECT 7200 65 CONNECT 33600
55 CONNECT 9600 66 CONNECT 38400
56 CONNECT 12000 67 CONNECT 48000
57 CONNECT 14400 68 CONNECT 56000
58 CONNECT 16800 69 CONNECT 64000
59 CONNECT 19200 70 CONNECT 112000
60 CONNECT 21600 71 CONNECT 128000
|
|