Elite 2864D - Onlinehilfe AT$

27758
E2864  V 3.01

Current settings .....
 B0   E1   L4   M1   N3   Q0   V1   X5  
&B1  &C1  &D2  &G0  &H3  &J0  &K4  &L0  &M0  &N0  &P0  &R1  &S0  &X0  &Y1  
*B0  *C0  *D0  *E0  *F0  *G0  *I0  *L0  *M0  *P11 *Q2  *S0  
S000=000 S001=000 S002=043 S003=013 S004=010 S005=008 S006=003 S007=060 
S008=002 S009=006 S010=007 S011=070 S012=000 S013=000 S014=002 S015=130 
S016=000 S017=022 S018=000 S019=000 S020=014 S021=178 S022=000 S023=105 
S024=067 S025=000 S026=000 S027=156 S028=068 S029=000 S030=000 S031=017 
S032=019 S033=000 S034=030 S035=032 S036=000 S037=000 S038=000 S039=032 
S040=000 S041=000 S042=000 S043=008 S044=000 S045=100 S046=028 S047=064 
S048=000 S049=006 S050=000 S051=000 S052=000 S053=000 S054=000 S055=000 
S056=000 S057=016 S058=002 S059=000 S060=002 S061=000 S062=000 S063=000 
S064=000 S065=000 S066=000 S067=000 S068=000 S069=000 S070=000 S071=064 
S072=000 S073=008 S074=000 S075=000 S076=000 S077=000 S078=000 S079=000 
S080=000 S081=000 S082=000 S083=000 S084=000 S085=000 S086=000 S087=000 
S088=000 S089=000 S090=000 S091=000 S092=000 S093=000 S094=000 S095=000 
S096=000 S097=000 S098=000 S099=000 S100=000 S101=000 S102=000 S103=000 
S104=000 S105=000 S106=000 S107=000 S108=000 S109=000 S110=000 S111=000 
S112=000 S113=000 S114=000 S115=000 S116=000 S117=000 S118=000 S119=000 
S120=000 S121=000 S122=000 S123=000 S124=000 S125=000 S126=000 S127=000

Elite 2864 User's Manual
Quick Reference Guide
For Firmware Version 3.00 and higher

Basic command summary &$ or &? Extended command summary *$ or *? Enhanced command summary #$ or #? Hash command summary +$ or +? FAX/Voice command summary A Answer incoming call H0 Hang up A/ Repeat last command H1 Off Hook A> Continuously repeat command I0 Product information B0 ITU-T answer sequence I1 Result of ROM checksum B1 Bell answer sequence I2 Link report Dn Dial a phone number Ln n=0-7, Speaker volume n=0...9*#TPR,;W@!( )- M0 Speaker always off DL Redial last dialed number M1 Speaker off during dialing DSn Dial stored phone number M2 Speaker always on n=0-49 M3 Speaker on until CD E0 Command echo disabled E1 Command echo enabled Nn n=0-7, Ring volume O0 Return on-line state O1 Like O0 with forced retrain P Pulse dialing Q0 Return result codes Q1 Quiet (no result codes) Q2 Quiet on answer mode only S$ or S? Summary of all S registers Sr.b=n Set bit .b of register r to n (*) Sr.b? Inquiry bit .b of register r (*) Sr=d Set register r to decimal value d, d=0-255 Sr=$h Set register r to hex value h, h=00-FF Sr=%b Set register r to binary value b, b=0-11111111 (*) Sr=\o Set register r to octal value o, o=0-377 Sr=? Inquiry summary of S register r Sr? Read contents of S register r (*) = ( 0/Off or 1/On ) T Tone dialing V0 Numeric result codes V1 Verbose result codes X0 Basic result codes (0-4) X1 Result codes (0-5, 10-21) X2 Result codes (0-6, 10-21) X3 Result codes (0-5, 7-21) X4 Result codes (0-21) X5 Error control result codes (0-21) X6 Error control result codes (0-21) X7 Error control result codes (0-21) Zn n=0-3, Reset modem and load user profile n n=4, Reset modem and load factory settings +++ Escape sequence code

Extended command summary &B0 DTE follows linked DCE rate &K0 No error control &B1 Fixed DTE rate &K1 MNP4 (include MNP3) &C0 CD always on &K2 MNP4 + MNP5 &C1 Track presence of carrier &K3 V.42 + &K1 &D0 Ignore DTR &K4 V.42 + V.42bis + &K2 &D1 108.1 &D2 DTR/108.2 &D3 108.2 + load profile 0 &F Load factory settings &L0 Dial up line &G0 No guard tone &L1 2 wire leased line &G1 Reserved &L2 4 wire leased line (e2864L only) &G2 1800 Hz guard tone &M0 Asynchronous data format &H0 Flow control disabled &M1 Async command, sync data &H2 Reserved &M2 Direct &H3 Hardware CTS/RTS &M3 Synchronous &H4 Local XON/XOFF &H5 Reserved &J0 Single phone line &J1 Multiple phone line (A/A1) &N0 Multi-Auto &N39 ZyXEL 7200 &N3 V.32 9600T/9600/7200T/4800 &N42 CELL 14400 &N4 V.32 9600/7200T/4800 &N43 CELL 12000 &N5 V.32 4800 &N44 CELL 9600 &N12 V.23 1200 &N45 CELL 7200 &N14 V.22bis 2400/1200 &N46 CELL 4800T &N15 V.22 1200 &N16 V.21 300 &N62 V.34 28800 &N17 V.32b 14400/12000/7200 &N63 V.34 26400 &N18 V.32b 12000/7200 &N64 V.34 24000 &N19 V.32b 7200 &N65 V.34 21600 &N24 Bell 212A 1200 &N66 V.34 19200 &N25 Bell 103 300 &N67 V.34 16800 &N32 FAX 14400 - 2400 &N68 V.34 14400 &N34 ZyXEL 19200 &N69 V.34 12000 &N35 ZyXEL 16800 &N70 V.34 9600 &N36 ZyXEL 14400 &N71 V.34 7200 &N37 ZyXEL 12000 &N72 V.34 4800 &N38 ZyXEL 9600 &N73 V.34 2400 &N78 V.90 56000 &N89 V.90 41333 &N79 V.90 54666 &N90 V.90 40000 &N80 V.90 53333 &N91 V.90 38666 &N81 V.90 52000 &N92 V.90 37333 &N82 V.90 50666 &N93 V.90 36000 &N83 V.90 49333 &N94 V.90 34666 &N84 V.90 48000 &N95 V.90 33333 &N85 V.90 46666 &N96 V.90 32000 &N86 V.90 45333 &N97 V.90 30666 &N87 V.90 44000 &N98 V.90 29333 &N88 V.90 42666 &N99 V.90 28000 &P0 M/B ratio = 39%/61% &Wn n=0-3, Save current settings to user &P1 M/B ratio = 33%/67% profile n &R0 CTS follows RTS &X0 Internal clock &R1 Ignore RTS &X1 External clock &S0 DSR always on &X2 Remote clock &S1 Data set ready &Y0 Destructive, expedited &T0 Terminate testing &Y1 Nondestructive, expedited &T1 Analog loopback test &Y2 Nondestructive, unexpedited &T3 Local digital loopback test &Zn=s Store the dial string s to EEPROM &T4 Grant RDL request at location n (0-49) &T5 Deny RDL request &Zn? Display the phone number stored &T6 Initiate RDL in EEPROM at location n &T7 Initiate RDL with self test &T8 Initiate ALB with self test &Vn n=0, View current settings n=1-4, View user profile n-1 settings n=5, View factory default settings

Enhanced command summary *B0 Disabled dial-backup *Bn n=1-9, Set dial-backup phone pointer at location n-1 *C0 10 Bit character length *C1 11 Bit character length *C2 9 Bit character length *C3 8 Bit character length *Dn n=0-5, Set default dial phone pointer at location n *E0 If error control negotiation fails, keep connection *E1 If error control negotiation fails, terminate the call *F0 Deny remote configuration *F1 Accept remote configuration *G0 Disable security function *G1 Enable type 1 security, with password check (ZyXEL to ZyXEL only) *G2 Enable type 1 Security, with password check and call back (ZyXEL to ZyXEL only) *G3 Enable type 2 security, with password check *G4 Enable type 2 security, with password check and call back *G5 Enable type 2 security, with password check and call back Remote site enter the call-back number *HS Modify supervisory password *S0 Secondary channel disabled *Hn Modify user password *S1 Secondary channel enabled *I0 AT command set *V View password table *I1 V.25 bis command set *T Recall the last CND(Caller-ID) *I2 Dumb mode *L0 Panel key normal *L1 Panel key locked *M0 Leased line auto handshake on originate mode *M1 Leased line auto handshake on answer mode *Pn n=0-15, Leased line transmission power level *Q0 No response to poor signal quality *Q1 Retrain action taken if signal quality is poor *Q2 Adaptive rate (auto fall back or fall forward) *Q3 Disconnect *Rab Read remote configuration *Wab Write local user profile to remote and to local profile reset remote modem from that profile a=0-3, Local user profile a=0-3, Local user profile b=0-3, Remote user profile a=4, Local active profile 4, Remote current profile a=5, Local factory default 5, Remote factory default b=0-3 Remote user profile 0-3

Hash command summary #Bn "CONNECT FAX" result code enable or disable n=0, Disable, used in ZFAX mode, normal operation (*) n=1, Enabled, for BBS fax receiving application, this command also changes "CONNECT 12000/ARQ" to "CONNECT 9600/ARQ". This will also send out external mail string "ZyXEL" when fax is connected, DCE will not send fax connection parameters until <DC2> is received from DTE n=2, Enable Polling feature of Fax. Modem will send polling signal to remote fax machine. n=3, Display ring cadence n=4, Disable Polling feature of Fax. #Cn Set minimun scan line time capability at the receiver n=0, 20 ms at 3.85 line/mm, T(7.7)=T(3.85) n=1, 5 ms at 3.85 line/mm, T(7.7)=T(3.85) n=2, 10 ms at 3.85 line/mm, T(7.7)=T(3.85) n=3, 20 ms at 3.85 line/mm, T(7.7)=1/2T(3.85) n=4, 40 ms at 3.85 line/mm, T(7.7)=T(3.85) n=5, 40 ms at 3.85 line/mm, T(7.7)=1/2T(3.85) n=6, 10 ms at 3.85 line/mm, T(7.7)=1/2T(3.85) n=7, 0 ms at 3.85 line/mm, T(7.7)=T(3.85) #En Display line conditions (if in On-Line state) n=0, Display mode off n=1, Display mode on #F Set the Modem into ZyXEL fax mode, same as AT&N32 #Ln Set maximum recording length n=0, Set maximum recording length, A4 (297mm) n=1, Set maximum recording length, B4 (364mm) n=2, Set maximum recording length, unlimited. #P<string> Set the local ID string, 25 characters max. #Rn Set recording width n=0, Set 1728 picture elements along a scan line length of 215mm n=1, Set 2048 picture elements along a scan line length of 255mm n=2, Set 2432 picture elements along a scan line length of 303mm #Tn Coding Scheme n=0, Set to one dimensional coding scheme n=1, Set to two dimensional coding scheme #Vn Vertical resolution n=0, Set to normal vertical resolution n=1, Set to high vertical resolution Result Code (with #B0) "CONNECT FAX/SnnnnVnTnRnLnCnP<string>" (with #B1) "/SnnnnVnTnRnLnCnP<string>" "DISCONNECTxP<string>" Snnnn First four digits of Fax connection speed Vn Vertical resolution; n =0-1 Tn Coding scheme; n =0-1 Rn Recording width; n =0-2 Ln Recording length; n =0-2 Cn Scan time; n =0-7 x Disconnect with confirmation (x=0) or without (x=1) P<string> Remote Fax number (*) Manufacture default (except when used to represent AT* commands)

FAX / Voice command summary +<command>=<value> Execute a command or set a parameter. +<command>=? Read permissible settings. +<command>? Read current setting. +FCLASS=n Service class selection. n=0 Set to modem mode. n=1 Set to Class 1 mode. n=2 Set to Class 2 mode. n=2.0 Set to Class 2.0 mode. n=6 Set to ZFAX mode. n=8 Set to Voice mode. n=Z Set to ZyXEL fax parallel port print and/or DRAM store mode. (See also class Z "AT+F" commands) 1. FAX, AT+V command summary 1b. Class 2.0 commands +FAA=n 2. Voice, AT+V command summary +FLO=n Flow control options. n=0 No flow control. n=1 * Set XON/XOFF software flow control. n=2 Set CTS/RTS hardware flow control. +VDD=<dds>,<ddi> Set the DTMF tone detection sensitivity threshold and the required period of continuous presence. <dds>=0-15 *5 Set DTMF detection threshold. A lower value means the DCE will detect DTMF tone more sensitively. A value of "0" disables DTMF detection <ddi>=0-255 *8 Set the duration of DTMF tone detection, in units of 5 ms. The modem reports DTMF event when it detects a continuous tone of at least this time interval A value of "0" disables DTMF detectio +VGR=n n=56-200 *0 Set the gain of received voice samples Higher value results in a larger gain (the normal value is 128). The value of zero is for DCE automatic gain control +VGT=n n=56-200 *128 Set the volume of playing voice Higher value results in a louder voice +VGN=n n=56-200 *60 Set the volume of playing tone Higher value results in a louder tone +VIP The DCE initializes all voice parameters to their default settings +VIT=n n=0-255 *70 Set the inactivity time-out timer value, in units of 0.1 second +VLH Request DCE hook status. n=0 DCE is on-hook. n=1 DCE is off-hook. +VLS=n Voice I/O device selection n=0 DCE is on-hook. Disconnect all I/O devices (local phone connects to telco line). n=1 Connects to local phone (PHONE jack.) DCE is on-hook n=2 DCE (modem) connects to telco line (Dial-up line jack). DCE is off-hook n=8 Connects to external mic. (local phone connects to telco line). DCE is on-hook n=16 DCE connects to internal speaker (use the internal speaker of the modem for voice playback, local phone connects to telco line), DCE is on-hook. +VNH=n Automatic hang-up options n=0 * DCE does not disable automatic hang-up n=1 DCE disables automatic hang-up usually found in other non-voice modes n=2 DCE disables automatic hang-up in other non- voice modes. DCE only performs a "logical" hang- up (it will not really hang-up on an ATH command) +VRA=n n=0-255 *70 Set the length of time the DCE shall wait between ringbacks before the DCE assumes remote station has gone off-hook, in units of 0.1 second +VRN=n n=0-255 *10 Set the length of time the DCE shall wait while looking for the first ringback before the DCE assumes remote station has gone off-hook, in units of 1 second. If the value of +VRN is larger than S7, will take effect +VRX Start the voice reception process +VSD=<sds>,<sdi> Set the silence detection sensitivity threshold and the required period of silence <sds>=0-31 *15 Larger value means the DCE treats noisier conditions as silence (the higher the value, the higher the sensitivity threshold level) Set value "0" to disable silence detection <sdi>=0-255 *70 In units of 0.1 second, required period of silence for detection +VSM=n Voice compression method selection n=2 * 19.2 Kbps 2-bit ADPCM n=3 28.8 Kbps 3-bit ADPCM n=30 30.72 Kbps new 3-bit ADPCM with resync capability n=4 38.4 Kbps 4-bit ADPCM +VSY=n n=0-255 *0 Set voice recording resync timer, in units of 50 ms. Set value "0" to disable resync generation +VTD=<dur>,<int> <dur>=0-255 *50 Set the DTMF tone generation duration used in conjunction with +VTS command, in units of 10 ms <int>=0-255 *7 set comma pause interval used in conjunction with +VTS command, in units of 10 ms +VTS=<string> Cause the DCE to generate DTMF and other tones Refer to 2864 series users manual for details +VTX Start the voice transmission process (*) Manufacturer default (Except when used to represent AT* commands) Snnnbx Cross reference to S-register number "nnn" bit number "x"